664065 660613 660743 Part No. Engine Length Diameter Includes Tank Fitting Includes Hose Fitting Tank End Includes Hose Fitting Engine End Primer Bulb Fuel Demand Valve 93806ELP7 Johnson/Evinrude 6’ 3/8” None 88896LP6 8889LP6 Multi-layer / Low Permeation No 93806EUS7 Johnson/Evinrude 6’ 3/8” 8838TM6 8838HF6 8889LP6 Multi-layer / Low Permeation No 93806MUS7 Mercury 6’ 3/8” 8838TM6 8838HF6 8896LP6 Multi-layer / Low Permeation No 93806ULP7 Universal 6’ 3/8” None None None Multi-layer / Low Permeation No 93806UUS7 Universal 6’ 3/8” 8838TM6 8838HF6 None Multi-layer / Low Permeation No 93806UUSD7 Universal 6’ 3/8” 8838TM6 8838HF6 None Multi-layer / Low Permeation Yes 93806YLP7 Yamaha 6’ 3/8” None 8896LP6 8896LP6 Multi-layer / Low Permeation No 93806YUS7 Yamaha 6’ 3/8” 8838TM6 8838HF6 8896LP6 Multi-layer / Low Permeation No 951606ULP7 Universal 6’ 5/16” None None None Multi-layer / Low Permeation No (A7J) Three-layer design resists collapsing and hardening and ensures high output in temperatures ranging from 18°F to 122°F. Includes high-efficiency check valves with Viton O-rings for improved sealing. Assembled with the same components as Mercury and Quicksilver. Low permeation for EPA/CARB compliance. Zero chance of material delamination. High-performance check valve O-rings provide 30% improved priming while keeping optimized flow during engine use (20 to 35% better than spring-loaded designs). EPA and CARB certified. Primer Bulbs (A7J) Eliminates engine flooding and spillage by preventing pressurized fuel from reaching the engine. The valve ensures that fuel is supplied to the engine only when demanded during start up or engine operation. Compatible with all OEM engine brands. Allows only the amount of fuel requested by the engine and prevents a pressurized “slug” of fuel from reaching engine. Compatible with 3/8” and 5/16” fuel hose. Low vacuum restriction helps ensure proper engine function during startup and engine operation. Built-in manual override. Compatible with Ethanol blended fuels. Fuel Demand Valve (A7J) Attwood’s low-permeation Fuel Line Kits set the standard in performance, safety and value. They include Attwood’s award-winning Universal Sprayless Connector (hose and tank fittings with thread sealant), multi-layer low-permeation Primer Bulb and low-permeation fuel line. Fuel Demand Valve is optional. • Multi-Layer Primer Bulb with new High-Performance Check Valve & O-Ring: Provides 30% faster priming during start-up and 20-35% higher running flow than competitive designs • Ethanol Resistant Fuel Line: Eliminates inner-layer delamination seen by others Fuel Demand Valve (if equipped): Prevents engine flooding by restricting pressurized fuel from reaching the engine • Universal Sprayless Tank Fitting: Enables a safe, gas-free experience at every connection Fuel Line Kits (A7J) On the exterior, they have a smooth edge over the competition. Unlike some others, there is no protruding cap to cause damage (or be damaged by) hull bumps and scrapes. Cap unscrews with hex head wrench for easy cleaning of filter and pressure testing of entire fuel system. These vents now include two silicone gaskets. Polypropylene Fuel Vent (A7J) Stainless Steel Alloy Flush-Mount Fuel Vents On the exterior, they have a smooth edge over the competition. Unlike some others, there is no protruding cap to cause damage (or be damaged by) hull bumps and scrapes. Cap unscrews with hex head wrench for easy cleaning of filter and pressure testing of entire fuel system. Includes two silicone gaskets. 660313 660323 (A7J) 90° P-Trap Fuel Tank Vents These vents help prevent water from entering the fuel tank, yet allow air to vent freely, during normal sea conditions and washdowns. This eliminates the need for an anti-siphon loop in the vent hose. For 5/8” I.D. hose. Meets ABYC standard.The arrows in this cross section show the based route that water would haYe to traYel in order to reach the fuel vent hose. Compatible with Ethanol blended fuels. 16746 16703 For 1-1/2” I.D. hose. Deck fills available with imprint to specify GASOLINE, DIESEL, WATER, or WASTE. Highly-polished finish. Flush cap is slotted for separate key and features an O-ring that seals the cap watertight. Cap is attached by a stainless steel beaded chain. 3-1/4” long fill neck. Key sold separately. 66126 waste model has internal threads for pump-out nozzle. Use for vessels with built-in holding tanks. Note: Requires a bonding wire to prevent sparking when nozzle is inserted on gas and diesel models per USCG and ABYC H-24 requirements. 1-1/2” Deck Fills (A7J) (W7E) Deck Plate Key (W7E) For Freshwater Use Only Stainless Steel Deck Fill Deck Fills are color coded and imprinted with international standard symbols Deck Fill with Splash Guard (W7E) Part No. Description 9300FDV7 In-Line Valve Part No. Description 6060C Fits all 316 SS Deck Fills Part No. Description 16073 Straight Vent, Black Part No. Description 664065 3-1/4”: Neck x 1-7/8” Hole x 3” Flange 660613 Repl. Cap and Chain For 3-1/2” Flanged Fill 660743 Repl. Cap and Chain Part No. Description 93014LP7 1/4” 93038LP7 3/8” 93516LP7 5/16” Part No. Description 660313 Straight Vent 660323 90° Vent Part No. Description 16703 Std. Mt. Black w/Black Vent Head 664193 Std. Mt. Black w/SS Trim Cover 9115261 Repl. Cover Std. Mt. 16746 Flush Mt., Black w/SS Vent Head Part No. Type Flange Hose Chain Fastener Material S7021C Gas 1-1/’2 3-1/8” Yes #10 (3) CP/Zamac S7022C Replacement Cap and Chain for S-7021 Part No. Type Flange Hose Angle Chain Fastener 6123C Gas 3” 1-1/2” 90° Yes #10 (3) 6061C Repl. Cap & Chain for 6123, 6124, 6125 & 6126 Motor & Lower Unit 636 Pricing subject to change without notice. Shop 24/7 at www.seawideb2b.com Fittings/Fuel Tanks/Plugs
RkJQdWJsaXNoZXIy MTAyMzU3Ng==