T-H Flex™ Sleeving Lightweight sleeving protects wire, cables and hoses. Braided from high temperature yarns and expands up to four times its normal diameter. Bulkhead Strain Relief Hose Kit Distributes strain from bends in hose. Water tight and great for hydraulic steering hose. Flange is 2-3/4” diameter and requires 1-1/4” installation hole. Part No. BSR1KDP Protects cables and wiring from elements. Molded polypropylene flange is threaded to retain hose. Vinyl cap provides closure for the engine end of hose. Kit includes flange and 4’ of rigging hose in black or chrome. Rigging Flange, Hose & Kits Part No. Description RF1DP Black, 2” RF2DP White, 2” RF251DP Black, 2.5” RFH1DP 2” Rigging Hose, Black 50’ Roll RFH2DP 2” Rigging Hose, White 50’ Roll RFK1CPDP 2” Chrome Rigging Flange Kit Protects cables, hoses, and wiring from elements. Molded polypropylene threaded flange to retain hose. Kit includes rigging hose and flange. Rigging Hose Kit Part No. Description RFK1DP 4’ Hose & 2” Flange, Black Part No. Description 16700001XD 5.8-7.0, 10-Pack 16700004XD 7.8-9.5 10-Pack 16700006XD 8.8-10.5 10-Pack 16700007XD 9.6-11.3 10-Pack 16700010XD 10.8-13.3 10-Pack 16700012XD 11.5-14.0 10-Pack 16700013XD 12.0-14.5 10-Pack 16700016XD 13.2-15.7 10-Pack 16700017XD 14.5-17.0 10-Pack 16700020XD 15.3-18.5 10-Pack 16700024XD 17.8-21.0 10-Pack 16700031XD 22.4-25.6 10-Pack 16700037XD 26.9-30.1 10-Pack 16700040XD 28.4-31.6 10-Pack 16705989XD 37.8-41.0 10-Pack Stepless clamps are available in key sizes and offer uniform compression and increased clamping force. Oetiker Stepless Ear Hose Clamps Nylon Cable Ties High tensile strength, lightweight, flexible made with nylon are non-corrosive cable ties. Easily support 50 lbs of force. Sizes ranging from 4”-14”. Part No. Description 075BRADCDP 7-1/2” Radiused Tie, Black 100/Pkg. 075BRADMDP 7-1/2” Radiused Tie, Black 1000/Pkg. Clam Shell Vent These super-strong molded clamshells are an economical and attractive alternative for metal clamshells. Use to route cables or wires through a hole or for covering thru-hull openings to shield water spray. Opening 9/16” H x 1 7/8” W. Base 2”x2”. Part No. Description CS1DP Black, Standard Vent CSS1DP Black, Small Vent Covers wire pass-thru holes. Provides a finished look for wiring. Wire Cover Part No. DWC1DP Provides a fully open area to pass wiring and cables through. Constructed of rugged black vinyl that resists ultraviolet rays, gasoline and oil. Cable Boots Part No. Description CB1DP 3” Cable Boot CB2DP 2” Cable Boot CB4DP 4-1/2” Cable Boot Reinforcing Cable Boot Rings Installs over the base flange of T-H Marine cable boots. Provides a neat and tidy trim. Reinforces the softer vinyl cable boot to protect it from pulling thru screws due to movement of cables. Part No. Description CBR1DP 3” Cable Boot Ring, Black CBR2DP 2” Cable Boot Ring, Black CBR4DP 4.5” Reinforced Cable Boot Ring, Black Part No. Description FLX50DP 1/2”, 100’ Spool FLX75DP 3/4”, 100’ Spool FLX150DP 1-1/2”, 50’ Spool Completes professional rigging installation and complies with ABYC-NMMA specifications. Split design of union allows installation on pre-rigged boats. Fuel hose ports ID = 3/4”. Install with 2” ID T-H Marine rigging hose. Rigging Flange with Fuel Hose Port & Rigging Flange Hose Union Part No. Description RFFHP1DP Fuel Hose Port, Black RFHU1DP Rigging Flange Hose Union (T9T) Motor & Lower Unit 752 Pricing subject to change without notice. Shop 24/7 at www.seawideb2b.com Rigging
RkJQdWJsaXNoZXIy MTAyMzU3Ng==